Most geometric typefaces start with a circle. ORRIN starts with a square. Every bowl, shoulder and terminal is cut at a right angle, so the letters sit on the grid like tiles.
ORRIN began as our logo. The Fonterio mark is an F built from two strokes on a square, with a single volt pixel blinking in the corner. When we tried to set the word “fonterio” next to it, nothing in our library felt like it came from the same hand. Round geometric sans looked soft beside the mark; condensed grotesques looked nervous. So we did what a type studio does when nothing fits: we drew the letters ourselves, on the same grid as the mark, and kept going until there was an alphabet.
One rule, many problems
A rule this strict creates hard letters. The S wants to curve. The g wants a loop. We solved each one by keeping the corner and moving the weight — thinner bars inside, heavier stems outside — so the counters stay open even at Black.
The rule is simple to say and slow to follow. Every outline in ORRIN is made of horizontal and vertical segments plus one permitted cut: a 45° chamfer where two strokes meet at a joint that would otherwise clog. There are no arcs anywhere in the font files. That forced a decision for every letter that is round in the alphabet we grew up reading, and a second decision for every diagonal.
Rounds without curves
The O is the key. Make it a perfect square and it looks bigger than the H and sits too wide on the line. We narrowed it by a grid unit, let it overshoot the baseline and cap height by a hair, and thinned the horizontals slightly so the vertical stems carry the colour. Once the O worked, the C, D, G and Q followed from it, each opening the square in a different place.
Diagonals on a grid
Letters like V, W, X and K cannot be squared without becoming unreadable, so ORRIN keeps their diagonals and squares their ends instead. Every diagonal terminal is cut flat to the baseline or the cap height, never angled, which keeps the rhythm of the line consistent with the straight-sided letters around them.
“The constraint did the design work. We just had to listen to it.”
Spacing a square font
Square shapes look wider than round ones, so ORRIN uses tighter side-bearings than you’d expect. We spaced the family from n and o outward, then tested it in long paragraphs before touching a single kerning pair.
In a round typeface the space between an n and an o is smaller than the space between two ns, because the curve of the o pulls away from its neighbour. In ORRIN the o has straight sides, so it behaves almost like a stem. That meant the usual ratios between straight and round side-bearings did not apply; Tomás rebuilt them from scratch and checked every lowercase letter in strings like the ones above until the texture went grey and even at reading distance.
Kerning came last and stayed small. Because the shapes are so regular, ORRIN needs far fewer pairs than a humanist sans. Most of the work went into combinations with open sides — T, L, r and the diagonals — where a square-cut terminal leaves a gap that the eye reads as a hole in the word.
What’s in the family
- Four weights: Light, Regular, Bold and Black
- Full Latin basic set with figures and punctuation
- OTF, TTF and WOFF2 files
The four weights share one skeleton. Light is drawn for large sizes, where its thin strokes look precise rather than fragile. Regular and Bold carry interface labels, navigation and short headings. Black is the poster weight, and it is where the rule earns its keep: as the strokes get heavier, the square counters would normally close up, so the inner bars thin out while the outer stems stay fat. Set a word in Black at 200px and the counters still read as clean rectangles.
Version one covers the basic Latin alphabet, figures and the punctuation you need for headlines and interfaces — 99 glyphs in all. Accented Latin, tabular figures and a matching mono are on the studio bench, and every buyer gets those updates as free downloads from their library.
Where it works best
ORRIN is a display and interface face, not a book face. Use it for logos, headlines, posters, navigation, buttons and short labels. For long reading, pair it with a quieter text face — we use it above a neutral grotesque throughout this site, and our pairing guide has more combinations that share its structural feel.
ORRIN is the font you’re reading in our headings and logo. Try it in the tester on its page, or license it for your next brand.
- Orrin
- release
- squared
- grid